Preface
This installation guide explains how to install the "ETERNUSmgr for Linux" storage system man-
agement software on an ETERNUS DX400 series, ETERNUS DX8000 series, ETERNUS2000,
ETERNUS4000, ETERNUS8000, ETERNUS3000, or ETERNUS6000 (hereafter referred to as
an "ETERNUS Disk storage system" or "device").
Follow the instructions in this guide to install "ETERNUSmgr for Linux".
Fourth Edition
October 2009
Content and Structure
This guide consists of the following two chapters and an appendix.
•
This chapter describes how to install ETERNUSmgr.
•
This chapter describes how to uninstall ETERNUSmgr.
An appendix describes the "How to Set Up the Web Server", using the "apache" Web server as a
typical example.
UNIX is a registered trademark of The Open Group in the United States and other countries.
Java and all Java-related trademarks, and logos are trademarks and registered trademarks of
Sun Microsystems, Inc. the United States and other countries.
Linux is a registered trademark, or a trademark of Linus Torvalds in the United States and other
countries.
Turbolinux and its logo are trademarks of Turbolinux, Inc.
Red Hat, RPM, and all Red Hat-based trademarks and logos are trademarks or registered trade-
marks of Red Hat, Inc. in the United States and other countries.
SUSE is a registered trademark of SUSE Linux AG., a subsidiary of Novell, Inc.
Microsoft is a registered trademark of Microsoft Corporation in the United States and other coun-
tries.
Netscape and Netscape Communicator are trademarks of Netscape Communications Corpora-
tion in the USA and other countries.
The company names, product names and service names mentioned in this document are
registered trademarks or trademarks of their respective companies.
Copyright 2009 FUJITSU LIMITED
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
3
Contents
Supported Environment ..................................................................................... 8
1.5.1 Web and Mail Server Installation and Setup ............................................................................. 10
1.5.2 Web Directory and Web Directory Files .................................................................................... 11
1.5.3 Editing the Top Menu File .......................................................................................................... 11
1.5.4 ETERNUSmgr Re-installation ................................................................................................... 11
1.6.1 Installation by rpm Command .................................................................................................... 12
1.6.2 ETERNUSmgr Environment Setup ............................................................................................ 12
Daemon Registration ....................................................................................... 18
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
4
Chapter 1 Installing ETERNUSmgr
This chapter describes how to install ETERNUSmgr.
1.1
ETERNUSmgr CD-ROM
The files distributed on the ETERNUSmgr CD-ROM are listed below.
• ./README_ja.TXT
• ./README_en.TXT
• ./bin/win/
• ./bin/sol/ETERNUSV20L30.PKG
• ./bin/hp/ETERNUSV20L30.HP
• ./bin/aix/ETERNUSV20L30.AIX
• ./bin/linux/FJSVgrmgr-V20L30-1.i386.rpm
• ./doc/install/win/
• ./doc/install/sol/
• ./doc/install/hp/
• ./doc/install/aix/
• ./doc/install/linux/
• ./doc/share/
• ./doc/DX8000/
• ./doc/E2000/
• ./doc/E3000/
• ./doc/E3000M50/
• ./doc/E4000M80/
• ./doc/E6000/
• ./doc/E8000M700/
• ./doc/E8000M800/
Each file and directory is briefly described below:
./README_ja.TXT
This file contains the CD-ROM list. (Japanese version)
./README_en.TXT
This file contains the CD-ROM list. (English version)
./bin/win/
This folder contains the files needed to install ETERNUSmgr for Windows. Use the
"SETUP.EXE" found in this folder to install these files.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
5
Chapter 1 Installing ETERNUSmgr
1.1 ETERNUSmgr CD-ROM
>
./bin/sol/ETERNUSV20L30.PKG
This is the main ETERNUSmgr program for Solaris. It is the installation package for the
"pkgadd" format.
./bin/hp/ETERNUSV20L30.HP
This is the main ETERNUSmgr program for HP-UX. This file is a compressed archive of the
various files needed to run ETERNUSmgr. Unpack this file and use the "stxinst" installer to
install these files.
./bin/aix/ETERNUSV20L3\30.AIX
This is the main ETERNUSmgr program for AIX. This file is a compressed archive of the
various files needed to run ETERNUSmgr. Unpack this file and use the "stxinst" installer to
install these files.
./bin/linux/eFJSVgrmgr-V20L30-1.i386.rpm
This is the main ETERNUSmgr program for Linux. It is the installation package for the "rpm"
format.
./doc/
This directory contains various manuals. Files with "EN" in their name are English version
manuals, while files without "EN" in their name are Japanese version manuals.
./doc/install/win/
This directory contains the "ETERNUS Disk storage systems ETERNUSmgr Install Guide for
Windows®" pdf files. These pdf files describe how to install ETERNUSmgr for Windows.
./doc/install/sol/
This directory contains the "ETERNUS Disk storage systems ETERNUSmgr Install Guide for
Solaris™ Operating System" pdf files. These pdf files describe how to install ETERNUSmgr
for Solaris.
./doc/install/hp/
This directory contains the "ETERNUS Disk storage systems ETERNUSmgr Install Guide for
HP-UX" pdf files. These pdf files describe how to install ETERNUSmgr for HP-UX.
./doc/install/aix/
This directory contains the "ETERNUS Disk storage systems ETERNUSmgr Install Guide for
AIX" pdf files. These pdf files describe how to install ETERNUSmgr for AIX.
./doc/install/linux/
This directory contains the "ETERNUS Disk storage systems ETERNUSmgr Install Guide for
Linux" pdf files. These pdf files describe how to install ETERNUSmgr for Linux.
./doc/share/
This directory contains the "ETERNUSmgr User Guide -Introduction-" pdf files. These pdf files
describe ETERNUSmgr's monitoring and e-mail notification functions.
./doc/DX8000/
This directory contains the "ETERNUS DX400/DX8000 series ETERNUSmgr User Guide -
Settings/Maintenance-" pdf files. These pdf files show how to set up an ETERNUS DX400
series or ETERNUS DX8000 series configuration, and describe how to modify its settings and
perform maintenance.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
6
Chapter 1 Installing ETERNUSmgr
>
1.1 ETERNUSmgr CD-ROM
./doc/E2000/
This directory contains the "ETERNUS2000 ETERNUSmgr User Guide -Settings/
Maintenance- for models 100 and 200" pdf files. These pdf files show how to set up an
ETERNUS2000 model 100 or 200 configuration, and describe how to modify settings and
perform maintenance.
./doc/E3000/
This directory contains the "ETERNUS3000 ETERNUSmgr User Guide -Settings/
Maintenance- for models 80, 100, 200, 200M, 300, 300M, 400, 400M, 500, 500M, 600, 600M,
700, and 700M" pdf files. These pdf files show how to set up an ETERNUS3000 model 80,
100, 200, 200M, 300, 300M, 400, 400M, 500, 500M, 600, 600M, 700, or 700M configuration,
and describe how to modify settings and perform maintenance.
./doc/E3000M50/
This directory contains the "ETERNUS3000 ETERNUSmgr User Guide -Settings/
Maintenance- for model 50" pdf files. These pdf files show how to set up an ETERNUS3000
model 50 configuration, and describe how to modify settings and perform maintenance.
./doc/E4000M80/
This directory contains the "ETERNUS4000 ETERNUSmgr User Guide -Settings/
Maintenance- for models 80 and 100" pdf files. These pdf files show how to set up an
ETERNUS4000 model 80 or 100 configuration, and describe how to modify settings and
perform maintenance.
./doc/E6000/
This directory contains the "ETERNUS6000 ETERNUSmgr User Guide -Settings/
Maintenance-" pdf files. These pdf files show how to set up an ETERNUS6000 configuration,
and describe how to modify settings and perform maintenance.
./doc/E8000M700/
This directory contains the "ETERNUS8000, ETERNUS4000 ETERNUSmgr User Guide -
Settings/Maintenance-" pdf files. These pdf files show how to set up an ETERNUS8000
model 700, 900, 1100, or 2100, and ETERNUS4000 model 300 or 500 configuration, and
describe how to modify settings and perform maintenance.
./doc/E8000M800/
This directory contains the "ETERNUS8000, ETERNUS4000 ETERNUSmgr User Guide -
Settings/Maintenance-" pdf files. These pdf files show how to set up an ETERNUS8000
model 800, 1200, or 2200, and ETERNUS4000 model 400 or 600 configuration, and describe
how to modify settings and perform maintenance.
ETERNUSmgr software, "ETERNUSmgr Install Guide", and/or "ETERNUSmgr User Guide" may
have been revised. The latest edition of each is available from the following site, and may be
downloaded as necessary.
• ETERNUSmgr software
• "ETERNUSmgr Install Guide" and "ETERNUSmgr User Guide"
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
7
Chapter 1 Installing ETERNUSmgr
1.2 Installation Outline
>
1.2
Installation Outline
The following are two stages in ETERNUSmgr installation.
(1) Installation by rpm command
(2) ETERNUSmgr environment setup
Check the following before installation.
• The IP address (provided by customer) of the ETERNUS Disk storage system
• The e-mail address of the system administrator (when using the e-mail notification function)
• The directory name on the Web server for the ETERNUSmgr menu file
• The URL for viewing the directory name on the above server using a browser
After installation, refer to the "ETERNUSmgr User Guide -Introduction-" to perform the necessary
settings.
For details about monitoring multiple target devices, refer to the "ETERNUSmgr User Guide
-Introduction-".
1.3
Supported Environment
•
Supported Operating Systems
• Red Hat Enterprise Linux AS (v. 3 for x86)
• Red Hat Enterprise Linux ES (v. 3 for x86)
• Red Hat Enterprise Linux AS (v. 4 for x86)
• Red Hat Enterprise Linux ES (v. 4 for x86)
• Red Hat Enterprise Linux AS (v. 4 for EM64T)
• Red Hat Enterprise Linux ES (v. 4 for EM64T)
• Red Hat Enterprise Linux 5 (for x86)
• Red Hat Enterprise Linux 5 (for Intel64)
• SUSE Linux Enterprise Server 9 for x86
• SUSE Linux Enterprise Server 9 for EM64T
• SUSE Linux Enterprise Server 10 for x86
• SUSE Linux Enterprise Server 10 for EM64T
ETERNUSmgr is not dependant on the kernel version.
Red Hat Enterprise Linux AS (v. 3 for Itanium), Red Hat Enterprise Linux
AS (v.4 for Itanium), Red Hat Enterprise Linux 5 (for Intel Itanium), SUSE
Linux Enterprise Server 9 for Itanium Processor Family, and SUSE Linux
Enterprise Server 10 for Itanium Processor Family are not supported.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
8
Chapter 1 Installing ETERNUSmgr
1.4 Required Hardware/Software
>
•
Supported Models
Refer to the specifications of each ETERNUS Disk storage system.
1.4
Required Hardware/Software
The following hardware/software is required in order to use "ETERNUSmgr".
• An Industry standard server with a Web server and Sendmail server installed
- IA-64 is not supported.
guaranteed.
- The Web server must be installed before installing ETERNUSmgr.
- Not restricted to any specific Web server. However, the Web server must have the
capability to display the HTML format log file list. Therefore, the Web server that will be
used must have the capacity to display the appropriate directories list.
- Sendmail is included with the Linux distribution.
• A client machine with the following software:
- For ETERNUS2000, use:
Software
type
Software name
Remarks
®
• Microsoft Internet Explorer 6.0 or later
Any of these
web browser
may be used.
Web
Browser
• Mozilla Firefox™ 1.5.0.10 or later
®
• Netscape 7.1 or later (Windows
environment)
• Java Runtime Environment 5.0 Update 11
or later
Java
Runtime
Environment
Either version
may be used.
• Java Runtime Environment 6.0 Update 3 or
later
- For ETERNUS GR series and ETERNUS3000 model 50, use:
Software
Software name
type
Remarks
®
• Microsoft Internet Explorer 5.5 + Service
Either web
browsers may
be used.
Web
Browser
Pack2 or later
• Netscape Communicator 4.5 or later
- For ETERNUS3000 (except model 50), and ETERNUS4000 models 80 and 100, use:
Software
type
Software name
Remarks
®
• Microsoft Internet Explorer 6.0 + Service
Pack1 or later
Either web
browsers may
be used.
Web
Browser
®
• Netscape 6.0 or later (Windows
environment)
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
9
Chapter 1 Installing ETERNUSmgr
1.5 Installation Notes
>
- For ETERNUS DX400 series, ETERNUS DX8000 series, ETERNUS4000 models 300,
400, 500, and 600, and ETERNUS8000, use:
Software
type
Software name
Remarks
®
• Microsoft Internet Explorer 6.0 + Service
Pack2
Any of these
web browser
may be used.
Web
Browser
®
• Microsoft Internet Explorer 7.0
®
• Netscape 6.0 or later (Windows
environment)
- For ETERNUS6000, use:
Software
type
Software name
Remarks
®
• Microsoft Internet Explorer 6.0 or later
Either web
browsers may
be used.
Web
Browser
• Netscape 6.0 or later
®
(Windows environment)
When a Web browser other than the ones listed above or an older version Web browser is
used, the screen display may be abnormal.
1.5
Installation Notes
1.5.1
Web and Mail Server Installation and Setup
To install the Web server and mail server, follow the procedures appropriate to the given
software.
For the Web server, setup the following two public directories.
• ETERNUSmgr Top Menu Directory
• ETERNUSmgr Alarm History Files Directory
The Web server must be set to allow the contents of the Alarm History Files Directory to be dis-
played. Note also that in the setup file (default filename "STXPOLL_1.INI") the
HTML_ALARMFILE_PATH parameter must be set to the Alarm History Files Directory.
The alarm history files must be saved in a directory immediately under the
directory in which the ETERNUSmgr Top Menu is installed.
See "ETERNUSmgr User Guide -Introduction-" for the details of the setup file.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
10
Chapter 1 Installing ETERNUSmgr
>
1.6 Procedure
1.5.2
Web Directory and Web Directory Files
Files in the Web directory created in the installation directory are ETERNUSmgr screen files (top
menu files). Copy the edited top menu ("menu.htm") and other related files to an appropriate
directory on the Web server containing the menu.
Note that the files need not be copied when the directory specified at installation is used and
changed as the location for the top menu, however if the menu is to be edited the top menu
should be saved under another name.
1.5.3
1.5.4
Editing the Top Menu File
As the ETERNUSmgr changes the content of the top menu ("menu.htm") in accordance with the
device's status at ETERNUSmgr start-up, do not overwrite or open the top menu with an editor
during ETERNUSmgr start-up. Always terminate ETERNUSmgr before making any changes to
the top menu.
ETERNUSmgr Re-installation
If ETERNUSmgr or GRmgr is already installed in a server where you want to install
ETERNUSmgr, uninstall the previous ETERNUSmgr or GRmgr before installing ETERNUSmgr.
ETERNUSmgr has compatibility with GRmgr V10L30 or later regarding logical operation, data
files, log files, etc. (it is not compatible with GRmgr V10L20 or earlier). ETERNUSmgr can use
setting file of GRmgr V10L30 or later. Before uninstalling GRmgr, make a backup of any setting
or log files, if necessary. For details, refer to "ETERNUSmgr compatibility with GRmgr" in "Chap-
ter 5 Cautions" in "ETERNUSmgr User Guide -Introduction-".
1.6
Procedure
This describes how to install ETERNUSmgr.
Before installing ETERNUSmgr, use the following format to check that ETERNUSmgr is not
installed. If ETERNUSmgr is already installed, uninstall it, and then install.
Format:rpm -qi FJSVgrmgr
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
11
Chapter 1 Installing ETERNUSmgr
>
1.6 Procedure
1.6.1
Installation by rpm Command
Execute "./bin/linux/FJSVgrmgr-VxxLxx-1.i386rpm" (which is an install package included with the
CD-ROM), by abiding by the following format. Installation must be conducted by the superuser. If
the installation directory is not specified, ETERNUSmgr will be installed in "/opt/FJSVgrmgr/" as
default. Refer to the entering "rpm" command in step 2 in the following, for installation directory
specification procedures.
Format:rpm -ivh FJSVgrmgr-V20L30-1.i386.rpm
* VxxLxx refers to the version/level number.
Procedure
1
2
Login as the superuser, and go to the directory where the install package is
located.
Follow the above format and enter the "rpm" command.
• When installing ETERNUSmgr V20L30 to the "/opt/FJSVgrmgr/" default directory
(Example) # rpm -ivh FJSVgrmgr-V20L30-1.i386.rpm
When specifying the installation directory, use the following example as a reference to
execute the "rpm" command.
Format:rpm -ivh --prefix "installation directory" FJSVgrmgr-V20L30-1.i386.rpm
• When installing ETERNUSmgr V20L30 to the "/usr/share/" directory
(Example) # rpm -ivh --prefix /usr/share FJSVgrmgr-V20L30-1.i386.rpm
3
This complete the installation with the "rpm" command.
If installation completed normally, the following message will appear:
(message displayed)
# Install of FJSVgrmgr completed.
End of procedure
Setup the environment settings by executing the ETERNUSmgr environment setup script.
ETERNUSmgr cannot activate normally if the environment is not set.
1.6.2
ETERNUSmgr Environment Setup
After installation by "rpm" is complete, a file for ETERNUSmgr environment setup script with the
name "stxpollset.sh," will be created in the installation directory (default is "/opt/FJSVgrmgr").
Transfer "stxpollset.sh" to the installation directory, and then execute.
Executing "stxpollset.sh" must be conducted by the superuser.
From here on, input each type of parameter by interacting with ETERNUSmgr environment setup
script "stxpollset.sh".
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
12
Chapter 1 Installing ETERNUSmgr
1.6 Procedure
>
Procedure
1
Select the type of target device.
The character string for the selected device is assigned to the "TARGET_TYPE"
parameter in the setup file ("STXPOLL_1.INI"), while a device type flag
(1=ETERNUS3000/GR710/GR720/GR730, 2=ETERNUS6000/GR740/GR820/GR840,
4=ETERNUS DX400 series/ETERNUS DX8000 series/ETERNUS2000/ETERNUS4000/
ETERNUS8000) is assigned to the "TARGET_FLAG" parameter.
For an ETERNUS DX410/DX440, select "1" (=ETERNUS DX400 series). For an ETER-
NUS DX8100/DX8400/DX8700, select "2" (=ETERNUS DX8000 series).
(message displayed)
# Select target type.
# 1=ETERNUS DX400 2=ETERNUS DX8000 3=ETERNUS2000 4=ETERNUS3000
5=ETERNUS4000 6=ETERNUS6000 7=ETERNUS8000 8=GR710 9=GR720 10=GR730
11=GR740 12=GR820 13=GR840
([1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13] default: 1=ETERNUS DX400)
2
Enter the URL.
Enter the URL for the directory in which ETERNUSmgr Top Menu is located. (The default
setting is "/opt/FJSVgrmgr/www".) (This URL is assigned to the ETERNUSmgr Top Menu
directory by the Web server settings.)
(message displayed)
# Input your www server URL.
# (default: http://)
3
4
Enter the Target Address.
a Enter the Target Address allocated to the device.
The value entered here is set to the "TARGET_ADDR" parameter of the
"STXPOLL_1.INI" file. Specify the IP address of the SVP when using SVP with the
ETERNUS6000.
(message displayed)
# Input target address (TARGET_ADDR).
# (default: 0.0.0.0)
Set the ETERNUSmgr e-mail notification function.
When the ETERNUSmgr e-mail notification function is to be used, set as follows:
a Enter the ETERNUSmgr Admin Mail Address.
ETERNUSmgr will send messages to the mail address entered here when a change of
status occurs in the device.
The value entered here is set to the "ADMIN_MAIL" parameter in the "STXPOLL_1.INI"
file.
(message displayed)
# Input ETERNUSmgr administrator mail address (ADMIN_MAIL).
# (default: root@domain-name)
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
13
Chapter 1 Installing ETERNUSmgr
1.6 Procedure
>
Note the following if you do not use the ETERNUSmgr e-mail notification function.
The "ADMIN_MAIL" parameter may be omitted in ETERNUSmgr in
order to disable the e-mail notification function. Note that the e-mail
notification function cannot be disabled by omitting the e-mail
address at installation, and the setup file must therefore be edited to
disable "ADMIN_MAIL". See "Chapter 2 Setup" in the
"ETERNUSmgr User Guide
-Introduction-" for details of editing the setup file.
If the mail settings are correct, ETERNUSmgr sends an e-mail which includes the
following message to the administrator when ETERNUSmgr is started.
"ETERNUSmgr VxxLxx - HTTP Polling engine was started."
*VxxLxx refers to the version/level number.
If no e-mail is sent to the administrator when ETERNUSmgr is started, the mail settings
are incorrect. Check whether the contents of the setup file are correct, and if there are any
problems in the transmission link.
Refer to "Chapter 3 Startup and Shutdown" in "ETERNUSmgr User Guide -Introduction-"
for details of starting ETERNUSmgr.
5
Check setup.
• If the settings are correct
Enter "y" and press the [Enter] key.
• If the settings are incorrect
Enter "n" and press the [Enter] key.
• To terminate installation
Press the [Ctrl] + [C] keys simultaneously.
→ Installation will be terminated.
(message displayed)
# WWW Server URL= "http://domain-name/ETERNUSmgr"
# Target Type= "ETERNUS3000"
# Target Address= "0.0.0.0"
# ETERNUSmgr Admin Mail Address= "root@grmacm2"
#
# Configuration OK?
6
ETERNUSmgr environment setup is complete.
If environment setup has ended normally, the following message will be displayed.
(message displayed)
Setup of FJSVgrmgr succeed.
End of procedure
Follow the procedure above to copy the necessary files to the specified installation directory. See
"Chapter 2 Setup" in the "ETERNUSmgr User Guide -Introduction-" for the necessary setups of
the ETERNUSmgr operation.
• Target Type
# Polling Server Type
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
14
Chapter 1 Installing ETERNUSmgr
1.6 Procedure
>
• Target Flag
# Polling Server Flag
GR730, 2 = ETERNUS6000, GR740, GR820, GR840, 4 = ETERNUS2000, ETERNUS4000,
ETERNUS8000, ETERNUS DX400 series, ETERNUS DX8000 series)
DX400".
DX8000".
The target type name can be modified post-installation.
• Target Address
# Polling Server Address
TARGET_ADDR = Target Address specified in Step 3
• Admin Mail Address
# Admin Mail Address
ADMIN_MAIL = Mail address specified in Step 4
• Alarm History Index URL
# HTTP Server URL
• Log Files Directory
# Log File Saved PATH
LOGFILE_PATH = Installation directory followed by "/log_1"
The parameters of the setup file can be edited after executing the environment setup script.
The settings to operate ETERNUSmgr by the Web are contained in ETERNUSmgr Top Menu
directory (default is "/opt/FJSVgrmgr/www"). For information on how to perform these settings,
refer to the Web server manual for further details.
The following files are stored in the installation directory, after installation by rpm and
ETERNUSmgr environment setup.
• stxpolld
• stxchk
• _STXPOLL.INI
• STXPOLL_1.INI
• stxpoll
• stxpollset.sh
• www/index.htm
• www/menu.htm
• www/fujitsu.gif, www/eternus.gif
The following explains each file and directory:
stxpolld
ETERNUSmgr daemon.
stxchk
Checks the ETERNUSmgr setup file.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
15
Chapter 1 Installing ETERNUSmgr
1.6 Procedure
>
_STXPOLL.INI, STXPOLL_1.INI
STXPOLL_1.INI is a setup file of ETERNUSmgr.
It is created by executing the environment setup script.
If necessary, a text editor such as Notepad, etc. can be used to edit these settings.
_STXPOLL.INI file is a template file.
Refer to the "ETERNUSmgr User Guide -Introduction-" when editing
these setup files. Edit only parameters described in the guide. Do not
delete comments or blank lines in the setup files during installation, and
do not add anything other than parameters. Failure to follow these
instructions may hinder performance and cause problems during future
upgrades.
The following format should be used for the file names.
Format:STX~.INI
If a file name is in a format other than specified above, ETERNUSmgr will not be able to find
the file. The only place the setup file can be saved is the installation directory. If saved to
another directory, the ETERNUSmgr cannot recognize where the setup files are saved.
The "STX~.INI" file name format must never be given to non-setup files
in the installation directory since, whether they are setup files or not,
ETERNUSmgr will attempt to read all such "STX~.INI" files, with
unforeseeable and potentially fatal results. If you want to make backup
files, save them with a different file name format, or save them outside
of the installation directory to prevent ETERNUSmgr from attempting to
use them.
ETERNUSmgr allows multiple setup files to be stored in the installation
directory, so error monitoring can be carried out for the specified devices
using the respective files. However, multiple monitoring settings cannot
be made for one device.
If multiple setup files for the same device are detected, a warning
message will appear and ETERNUSmgr will not start up. For further
details, refer to "2.5 Monitoring Multiple Target Devices" in the
"ETERNUSmgr User Guide -Introduction-".
stxpoll
Execution control script for starting up or stopping the ETERNUSmgr.
stxpollset.sh
Shell script to conduct environment setup after installation by rpm. Creates the ETERNUSmgr
setup file "STXPOLL_1.INI". "stxpollset.sh" can be executed many times, but if it is executed
when "STXPOLL_1.INT" already exists, the setup file will be overwritten, so caution is
advised. If "stxpollset.sh" needs to be executed a second time, first backup the
ETERNUSmgr setup file, and then execute.
www/index.htm
This file contains the initial screen. After 5 seconds, it automatically jumps to the
ETERNUSmgr Top Menu.
To use this file, copy it to a directory under the Web server where the top menu is stored.
During installation, there is no need to copy this file to the specified directory under the top
menu if the default directory is used.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
16
Chapter 1 Installing ETERNUSmgr
1.6 Procedure
>
www/menu.htm
This file contains ETERNUSmgr Top Menu.
To use this file, copy it to a directory under the Web server where the top menu is stored.
During installation, there is no need to copy this file to the specified directory under the top
menu if the default directory is used. In this case, make a backup of this file ("menu.htm") and
save it under a different name.
www/fujitsu.gif, www/eternus.gif
These are the images used by the ETERNUSmgr screens.
To use them, copy them to a directory under the Web server where the top menu is stored.
During installation, there is no need to copy these files to the specified directory under the top
menu.
setup/
The directory storing the file that the environment setup script uses for environment setup of
ETERNUSmgr.
• The "www/index.htm," "www/menu.htm," "www/fujitsu.gif" and "www/
eternus.gif" files must be copied to the same directory under the Web
server where ETERNUSmgr Top Menu is stored.
• Always perform the copy operation stated above when
ETERNUSmgr is in a stopped state. In addition, if the copy
destination of files "www/index.htm," "www/menu.htm," "www/
fujitsu.gif" and "www/eternus.gif" is different from the location at
installation, make sure to copy them to the same directory, edit all the
setup files ("STX~.INI"), and specify the copy destination for
"HMTL_ALARMFILE_PATH". Also, set the link to the alarm file for
each device described under "Show hardware error detect log list" in
the top menu ("menu.htm") to be the same as the setup file's
"HTML_ ALARMFILE_PATH".
See "ETERNUSmgr User Guide -Introduction-" for the procedures for editing individual files.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
17
Chapter 1 Installing ETERNUSmgr
1.7 Daemon Registration
>
1.7
Daemon Registration
This section describes how to register ETERNUSmgr daemon. The location and procedure to
register the daemon may vary depending on the server settings (registration locations vary with
the run level).
Consult with the server administrator to register the daemon.
1
2
Login as superuser.
Copy the execution control script to /etc/init.d/ directory.
# cp /opt/FJSVgrmgr/stxpoll /etc/init.d/
3
Create the link to the appropriate rc*.d directory.
# ln -s /etc/init.d/stxpoll /etc/rc5.d/Snnstxpoll (nn is a number)
"nn" in Snnstxpoll indicates the order of priority. Set any order of priority. Consult with the server
administrator for setting priority.
(Example) # ln -s /etc/init.d/stxpoll /etc/rc5.d/S98stxpoll
The ETERNUSmgr will be automatically started as a daemon from the next server startup. Make
sure that ETERNUSmgr has begun communication with the device by checking the log file after
server startup.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
18
Chapter 2 Uninstalling ETERNUSmgr
This chapter describes how to uninstall ETERNUSmgr.
Always terminate ETERNUSmgr before uninstalling.
For details of terminating ETERNUSmgr, refer to "Chapter 3 Startup and Shutdown" in the
"ETERNUSmgr User Guide -Introduction-."
Use the "rpm" command to uninstall.
Format: rpm -e FJSVgrmgr
Procedure
1
2
Log in as the superuser.
Follow the above format and enter the "rpm" command.
# rpm -e FJSVgrmgr
3
This completes the uninstall.
If uninstall has ended normally, the following message will be displayed.
(message displayed)
# Uninstall of FJSVgrmgr completed.
End of procedure
When ETERNUSmgr is registered as a daemon, ensure that the created links and copied
execution control script are also deleted.
Before uninstalling, save the setup file ("STX~.INI") in the ETERNUSmgr installation directory as
necessary. The setup file contains the device IP address and administrator's e-mail address etc.,
and may be useful as reference when installing ETERNUSmgr again. The log file and Alarm
history files generated when ETERNUSmgr is started contain a cumulative history of the
operating status for the ETERNUSmgr and the device, and should be saved as necessary.
Uninstall deletes files that have been installed, but does not delete some files and directory.
The following are the files and directory that are not deleted.
• ETERNUSmgr setup file "STX~.INI"
• Log files of each type created by ETERNUSmgr
• Directories created by ETERNUSmgr
Files and directories are required to be deleted manually.
(When ETERNUSmgr installation directory is "/opt/FJSVgrmgr")
# rm -r /opt/FJSVgrmgr
After uninstalling ETERNUSmgr, verify prior to the new installation that the directory does not
exist, or that the directory does not contain files or directories, before reinstalling in the same
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
19
Chapter 2 Uninstalling ETERNUSmgr
>
directory. If installed again while previous ETERNUSmgr files exist, the installation may not be
completed, or may not operate correctly. This is particularly relevant when the previous setup file
("STX~.INI") remains and is later detected by ETERNUSmgr during operation.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
20
Appendix A How to Set Up the Web Server
In addition to installing ETERNUSmgr, your Web server may need to be appropriately set up to
enable faults to be monitored and the device status displayed using a Web browser.
This appendix introduces an example of how to install ETERNUSmgr and how to set up apache,
a typical Web server.
The following describes an example of "apache 1.3.20" as the Web server. The directory
configuration to be installed, setup method, and name or content of setup file sometimes vary
according to differences between apache versions and the version of the OS. If the settings of
the apache you are using are not as shown in this example, rewrite the relevant items.
ETERNUSmgr is not dependent on Web server type. However, the Web server should have the
capability to display an appropriate directory list for an HTML format log file list. Also,
ETERNUSmgr does not recommend or guarantee use of apache as the Web server.
For details on how to install the Web server or the setup method, refer to the relevant documents
(User's Manual of the Web server you are using, etc.).
■ Example 1
Setting up the ETERNUSmgr Top Menu directory as the Web server top public directory (root)
when installing ETERNUSmgr using the default settings.
[Assumptions]
• apache is already installed under the following directory configuration
Root path for apache HTML
: "/home/httpd/html"
document
Full path of apache setup file
: "/etc/httpd/conf/httpd.conf"
• ETERNUSmgr is installed under the following settings
Directory of top menu
Directory of top menu
: "/opt/FJSVgrmgr/www"
[Web server setup procedure]
Procedure
1
2
Open the apache setup file "httpd.conf" in an editor (e.g. vi).
Search for the line described as "DocumentRoot" in "httpd.conf."
(example of "httpd.conf")
#
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
#
DocumentRoot "/home/httpd/html"
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
21
Appendix A How to Set Up the Web Server
>
3
Correct the path set in "DocumentRoot" to the directory of the ETERNUSmgr Top Menu.
(Change underlined section below.)
(example of "httpd.conf")
#
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
#
DocumentRoot "/opt/FJSVgrmgr/www"
4
5
Add the directory option setting (setting to display the directory list).
<Directory "/opt/FJSVgrmgr/www">
DirectoryIndex index.htm
Options Indexes MultiViews
AllowOverride None
Order allow,deny
Allow from all
</Directory>
Reboot apache.
End of procedure
■ Example 2
Setting up the ETERNUSmgr Top Menu directory as a Web server public directory ("/
ETERNUSmgr") when installing ETERNUSmgr using the default settings.
[Assumptions]
• apache is already installed under the following directory configuration
Root path for apache HTML
: "/home/httpd/html"
document
Full path of apache setup file
: "/etc/httpd/conf/httpd.conf"
• ETERNUSmgr is installed under the following settings
Directory of top menu
: "/opt/FJSVgrmgr/www"
ETERNUSmgr"
URL for above directory
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
22
Appendix A How to Set Up the Web Server
>
[Web server setup procedure]
Procedure
1
2
Open the apache setup file "httpd.conf" in an editor (e.g. vi).
Search for the line described as "Alias" in "httpd.conf."
(example of "httpd.conf")
#
# Note that if you include a trailing / on fakename then the server will
# require it to be present in the URL. So "/icons" isn't aliased in
this
# example, only "/icons/"..
#
Alias /icons/ "/home/httpd/icons/"
<Directory "/home/httpd/icons">
Options Indexes MultiViews
AllowOverride None
Order allow,deny
Allow from all
</Directory>
3
Add the directory of the ETERNUSmgr Top Menu to the apache Alias. (Add underlined
section below.)
(example of "httpd.conf")
#
# Note that if you include a trailing / on fakename then the server will
# require it to be present in the URL. So "/icons" isn't aliased in
this
# example, only "/icons/"..
#
Alias /icons/ "/home/httpd/icons/"
<Directory "/home/httpd/icons">
Options Indexes MultiViews
AllowOverride None
Order allow,deny
Allow from all
</Directory>
Alias /ETERNUSmgr/ "/opt/FJSVgrmgr/www/"
<Directory "/opt/FJSVgrmgr/www">
Options Indexes MultiViews
AllowOverride None
Order allow,deny
Allow from all
</Directory>
4
Reboot apache.
End of procedure
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
23
Appendix A How to Set Up the Web Server
>
■ Example 3
Setting up the ETERNUSmgr Top Menu in the previously used Web server public directory when
installing ETERNUSmgr.
[Assumptions]
• apache is already installed under the following directory configuration
Root path for apache HTML
: "/home/httpd/html"
document
Full path of apache setup file
: "/etc/httpd/conf/httpd.conf"
• ETERNUSmgr is installed under the following settings
Directory of top menu
: "/home/httpd/manual/ETERNUSmgr"
ETERNUSmgr"
URL for above directory
[Web server setup procedure]
When the directory of the ETERNUSmgr Top Menu is created under the
root path of the apache HTML document, and the name of the URL
directory matches the name of the directory under the root path, measures
such as changing the setup on apache or restarting the Web server are not
required.
For example, when apache is set to automatically restart after the OS is rebooted, and the
startup shell script is "/etc/init.d/httpd," apache can be restarted by the following method:
/etc/init.d/httpd restart
For details, refer to the relevant materials for the Web server you are using.
P2U3-0022-04ENZ0 ETERNUS Disk storage systems ETERNUSmgr Install Guide for Linux
Copyright 2009 FUJITSU LIMITED
24
ETERNUS Disk storage systems ETERNUSmgr Install Guide
for Linux
P2U3-0022-04ENZ0
Date of issuance: October 2009
Issuance responsibility: FUJITSU LIMITED
•
•
The contents of this manual are liable to being updated without notice.
While the contents of this manual are the product of all due care and diligence, no
responsibility can be accepted for operational problems arising from any errors or
missing information, or other use of the information contained in this manual.
•
•
Fujitsu assumes no liability for damages to third party copyrights or other rights arising
from the use of any information in this manual.
Contents of this manual are not to be reproduced without permission from Fujitsu.
|